Wakol MS 550 Polymer PVC and Rubber Glue (contents 7.5kg),

For the installation of homogeneous and heterogeneous PVC flooring in rolls and tiles, PVC design flooring, central heating flooring, as well as rubber flooring in rolls and tiles, needle felt flooring, linoleum, PVC cork flooring, artificial grass, and entrance mats on absorbent and non-absorbent subfloors indoors and outdoors. Waterproof. WAKOL MS 550 complies with DIN EN 14259.

Application: adhesive comb according to TKB A1, A2, B1 or B2

Consumption: approx. 300-580 g/m²

Waiting time: approx. 0-20 minutes

Opening time: approx. 35 minutes

Storage: not frost sensitive

Raw material base: MS polymer

EMICODE: EC1 PLUS R
For sale per piece, multiple pieces, or per pallet(s) (72 pieces)

WAKOL MS 550 PVC and rubber adhesive – the first MS adhesive for PVC floor coverings

Modern reaction adhesive for elastic floor coverings,
With WAKOL MS 550 PVC and rubber adhesive, it is now possible for the first time to safely carry out demanding installations that previously had to be carried out with 2-component PU adhesives using a modern, single-component MS adhesive.

Very broad application spectrum,
WAKOL MS 550 PVC and rubber adhesive is suitable for bonding all PVC floor coverings, as well as PVC design floor coverings, to rubber floor coverings. It doesn't matter whether you want to install the floor covering on absorbent or non-absorbent substrates, indoors or outdoors.

For the highest demands on the installed surface,
Areas with high moisture levels, such as access zones or areas subject to increased heat from sunlight, such as conservatories, can be reliably installed with WAKOL MS 550 PVC and rubber adhesive. Challenges such as surfaces subject to forklift traffic and heavy loads are handled by the secure and strong bond.

Start immediately and use surface quickly,
WAKOL MS 550 PVC and rubber adhesive is applied directly from the bucket to the prepared substrate without the need for complicated mixing. Because the adhesive can also be used on non-absorbent substrates, surfaces primed or sealed with materials such as WAKOL PU 280 Polyurethane Primer or WAKOL MS 325 Silane Primer can also be treated directly.

Processing comfort and safe application,
WAKOL MS 550 PVC and rubber adhesive is characterized by a very low tendency to compress. When working on the floor covering, such as when installing roll-fed flooring, it minimizes knee marks. Thanks to its high initial tack and fast drying, PVC design floor coverings stay firmly in place from the start. Any adhesive that spills onto the floor covering can be
It can be removed without residue when fresh and cured. Due to the hard adhesive beads of WAKOL MS 550 PVC and rubber adhesive, residual impressions are minimized just as effectively as with a fiber-based dispersion adhesive.

Long shelf life due to sealed bucket,
WAKOL MS 550 PVC and rubber adhesive is supplied in a practical plastic bucket. An aluminum composite foil, welded to the edge of the bucket, provides optimal moisture protection and guarantees a shelf life of at least 12 months. This eliminates the risk of curing in the unopened original bucket and the associated material loss and additional costs.

Economic,
As a single-component product, WAKOL MS 550 PVC and rubber adhesive eliminates the hassle and time-consuming mixing process. This means that, unlike with two-component PU adhesives, you don't need mixer power on the construction site. You won't have to worry about dirty stirring tools or lost time mixing. Mixing errors are also a thing of the past. Waiting times are no longer necessary with this modern product. You won't lose money due to cured residue, which is unavoidable with two-component products. After covering the residue and closing the container, the adhesive can be used for subsequent work. Therefore, there is virtually no residual waste.

Please always observe the technical information before processing

--TECHNICAL INFORMATION--

--TECHNICAL INFORMATION-2-