Loba 2K Intensive Color,

Lobadur® HS 2K Intensive AT is a high-solids, oil-based primer for parquet flooring. It significantly enhances the wood's color, creating the richness of an oiled floor. Easy and reliable to use, it works with all Lobadur® WS lacquers in all gloss levels.

• Clear intensification of the wood colour
• Cobalt and butanone oxime free
• Combines an oiled look with the advantages of lacquer
• Safe and easy processing
• No roughening of the wood
• No edge-gluing effect.

Can be overcoated after at least 12 hours. If drying problems occur, wait for complete drying.

Lobadur® HS 2K Intensive AT is suitable for virtually all European and exotic wood species. Please refer to the Lobadur wood species list. If in doubt, consult your doctor. The edge-bonding effect of water-based varnishes is reduced. Block bonding does not occur with professionally installed, impact-resistant, and elastically bonded parquet and wooden floors.

This is the Chalk variant in 2.5kg.

Scope of application :
Suitable for virtually all European and exotic wood species. Refer to the LOBA wood species list. If in doubt, consult a qualified professional. The edge-bonding effect of water-based lacquers
is reduced. With professionally installed, impact-resistant, elastically bonded parquet and wooden floors, no block bonding occurs.

Instructions for use Loba Intensive Color,

Stir the a-component, add the hardener in a 5:1 ratio, and mix everything mechanically with a LOBA paint mixer. If smaller quantities need to be mixed, use the LOBA mixing cup or weigh the mixture. After mixing, it can be processed for 2 hours.
• In weather conditions on the construction site with 50% relative humidity or more, it is important to provide air circulation with fans.
• The surface must be properly sanded. The floor must be dry and free of any old layers, oil, grease, wax, silicone, sanding dust, and other contaminants.
• The optimum processing conditions are a room temperature of +15°C to + 25°C, a floor temperature of +15°C to +22°C, a relative humidity of 40% - 65%, a material temperature of +18°C - + 25°C, a maximum wood moisture content of 12%, and adequate ventilation of work areas.
• To prevent damage to the parquet, the expected annual average room climate for use must be observed during processing.
• Do not pour material on the floor, use a LOBA paint bucket
• Stir material well.
• The original color of the wood used, its structure and absorbency, as well as the fineness of the sanding pattern, have a strong influence on the resulting color. We strongly recommend creating color samples on the original wood using the final sanding method for your own testing and, if necessary, for approval by the client.
• Observe the LOBA "Sanding tips for pre-colouring parquet floors".
Before using the Color variant, we recommend creating a test piece to assess whether the desired color can be achieved through optical interaction. The colors are intermixable. The transparent variant can be mixed in to increase transparency and reduce opacity. For a consistent color appearance, saturating the pigments is essential; therefore, the color can be diluted with a maximum of three parts transparent to one part color.
• If more than one container is used for a large surface, the total quantity should be mixed together at once.
• Observe general and product-specific protective measures.

• The product is ready to use and must not be diluted!
• LOBA oil roller Microfiber 60-80 / approx. 20-40 g / m² (25-50 m² / kg) depending on the absorbency of the surface.
• Do not sand the base coat between coats.
• • Can be painted over after at least 12 hours.
  • In case of drying problems, wait for complete drying.
• LACQUERS SUITABLE FOR OVERLAPPING:
  • 2K InvisibleProtect
  • 2K Supra AT
  • 2K Duo.
  • 2K Fusion.
  • EasyFinish.
• OPTIONAL PRETREATMENT FOR SPECIAL EFFECTS
  • PreTone
• BUILDING ADVICE FOR ROLLER APPLICATION:
  • Apply a base coat thinly with the oil roller below, microfibre 60/80.
  • After a processing time of approx. 30-60 minutes, carefully level out the surface using a single-disc machine and the LOBA Normal pad beige, completely removing any excess material.
  • Allow to dry for at least 12 hours
  • Apply LOBA water-based varnish with the roller below (according to the technical specifications).
  • Intermediate sanding with a sanding fleece and sanding strips P240.
  • Apply LOBA water-based varnish with the roller below (according to the technical specifications).
  
  --BROCHURE + INFORMATION...